本目錄是上海蘇特電氣有限公司為您精心選購的：
FDB型35KV放電棒
（一）FDB型放電棒概述：
在高壓試驗領域內，為了保證高壓試驗人員人身安全和設備正常運行，安全措施非常重要。我廠生產的FDB型高壓直流放電棒，就是為了配電系統及電力用戶在現場檢測各種高壓電器設備的絕緣性能時，確保人身安全的一種產品。
（二）FDB型35KV放電棒配置：
銅線規格：25mm2
銅線長度：4m
接地端：接地夾
接地端材質：鋁
（三）FDB型35KV放電棒的工作原理
在進行沖擊和直流高壓設備以及較大電容的試品試驗時，由于試品在試驗線路中為容性負載，當斷開試驗線路時，試品上將有殘余電荷存在，形成一個高電位。將會發生暫態電流電擊而造成人身事故，為了防止這種現象發生，試驗人員在改核核線時，可用我廠生產的FDB型高壓直流放電棒在試品，使其殘余電荷接地在接觸試品，為使放電更安全，放電棒內還加裝了限流電阻。
（四）的使用方法
將便攜式伸縮新型放電棒伸縮部分全部拉出。然后再將配置好的接地線插頭插入放電棒的頭端部位的插孔內，將地線的另一端與大地連接，放電完畢后，既直流發生器的控制箱的升壓璇鈕回到零位上，此時可觀察控制箱上的電壓表的電壓降到15KV~20KV左右，方可放電。放電過程中應先用放電棒的前端的金屬尖頭，慢慢的去靠近已斷開試驗電源的試品。此時放電棒釋放電能是經過放電電阻進行對地放電。然后再用放電棒上的鉤子去鉤住試品，進行第二次防電。
（五）放電棒的使用注意事項
1、放電前應先檢查放電棒接地端后與接地線連接是否牢靠。
2．對幾公里以上的高壓電纜試驗結束后，放電時間一般很長，且需多次反復放電。電阻容量要很大，需訂購大容量的放電棒。
3．嚴禁未拉開試驗電源用放電棒對試品進行放電。
4．嚴禁用腳踩及重物擠壓放電棒，嚴禁折彎，折斷放電棒。
5．嚴禁將放電棒受潮，影響絕緣強度，應放在干燥的地方。
6．放電時工作人員不可接觸地線
